Strong Initial Results from RC Drilling at Cummins Range
Released
Released
Announcement PDF
ASX / MEDIA ANNOUNCEMENT
9 September 2021
STRONG INITIAL RESULTS FROM RC DRILLING EXPAND
SIZE OF MAIN FAULT AND DISCOVER NEW NORTHERN
MINERALISED FAULT
First batch of assays confirm true width of the Main Fault to be >40m and identify new
mineralised position, highlighting the deposit’s exceptional growth potential
HIGHLIGHTS
• CRX0063 intersects multiple mineralised zones including:
- Main Fault – 41m at 2.4% TREO and 0.51% Nb2O5 from 57m, including:
- 10m 4.1% TREO and 0.75% Nb2O5
- Secondary Zone – 28m at 0.8% TREO and 0.24% Nb2O5 (open at depth and down-dip)
• Northern Fault discovered parallel to the Main Fault
• Follow-up diamond drilling targeting depth extensions continuing
RareX Limited (ASX: REE; RareX or the Company) is pleased to advise that it has received highly
encouraging initial results from the recently completed initial phase of 1500m of reverse
circulation (RC) drilling at its flagship Cummins Range Rare Earths Project in the Kimberley region
of Western Australia.
The RC drilling was designed to test both the Company’s geological interpretation prior to the
commencement of the diamond drilling and to test areas for new mineralised trends.
The program has proven to be successful on both counts, highlighting the exceptional scope to
grow the Cummins Range Mineral Resource.
Drilling on the north-western end of the Main Fault Zone exceeded expectations and has
intersected wide zones of high-grade rare earths for a cumulative down-hole width of 88m in
CRX0063 including a higher-grade zone of 41m at 2.4% TREO and 0.51% Nb205 including 10m @
4.1% TREO and 0.74% Nb2O5 in the interpreted Main Fault position.
A secondary zone below this also intersected 28m at 0.8% TREO and 0.24% Nb2O5 in fresh rock
to the end-of-hole. The holes were drilled perpendicular to the Main Fault at 50 degrees azimuth
and, from geological interpretations, the drilled intersections are true width.
A follow-up diamond drill hole is being planned to test for mineralisation down-dip of this
intercept.
Diamond drilling down-dip of these high-grade intercepts will assist the Company’s geological
team to better understand the geological controls on the Main Fault Zone and to target further
diamond drill holes.
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
1
Figure 1 - Cummins Range Schematic Cross Section Main Fault
Figure 2 - Cummins Range Plan
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
2
These RC drill results have also confirmed the discovery of a second parallel mineralised
structure called the Northern Fault with intercepts including 15m at 1.1% TREO and 12m at 1.1%
TREO.
Further drilling is planned to test for extensions of this structure both along strike and at depth.
Figure 3 - Cummins Range Schematic Section Northern Fault
Diamond drilling is continuing with results to be provided to the market when available.
This announcement has been authorised for release by the Board of RareX Limited.
For further information, please contact:
RareX Limited
Jeremy Robinson
Executive Director
Ph: 08 6143 6720
Media Enquiries
Nicholas Read
Read Corporate
Ph: 08 9388 1474
Competent Person’s Statements
Information in this release that relates to Exploration Results is based on and fairly represents information and
supporting documentation reviewed or compiled by Mr Guy Moulang, an experienced geologist engaged by RareX
Limited. Mr Moulang is a Member of the Australian Institute of Geoscientist and has sufficient experience which is
relevant to the styles of mineralisation and types of deposits under consideration and to the activities being
undertaken to qualify as a Competent Person as defined in the 2012 Edition of the “Australasian Code for Reporting
of Exploration Results, Mineral Resources and Ore Reserves”. Mr Moulang consents to the inclusion in this release
of the matters based on his information in the form and context in which it appears.
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
3
Appendix 1: Drill Collar Details
Hole ID
CRX0059
CRX0060
CRX0061
CRX0062
CRX0063
CRX0064
CRX0065
CRX0066
CRX0067
CRX0068
CRX0069
CRX0070
East MGA
307462
307139
306998
307223
307106
307399
307530
307348
307435
307430
307454
307477
North MGA
7866481
7866751
7866604
7866709
7866720
7866736
7866370
7866540
7866712
7866762
7866679
7866648
End Depth
96
120
120
108
144
120
120
132
120
96
120
144
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
Azimuth
50
50
50
50
50
50
50
90
50
50
50
50
Dip
60
60
60
60
60
60
60
0
60
60
60
60
Type
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
Assays
Received
Received
Received
Awaiting
Received
Received
Awaiting
Awaiting
Awaiting
Received
Awaiting
Awaiting
4
Appendix 2: Significant Results
HoleID
CRX0059
CRX0059
Incl.
CRX0059
CRX0059
CRX0060
CRX0060
CRX0060
Incl.
CRX0061
CRX0061
CRX0061
CRX0061
CRX0063
CRX0063
CRX0063
Incl.
CRX0063
Incl.
CRX0064
Incl.
CRX0068
CRX0068
CRX0068
From
1
19
21
64
90
12
28
42
56
10
21
30
90
18
46
57
72
116
129
81
81
43
58
64
To
6
32
22
66
95
14
35
78
59
12
25
32
95
34
49
98
82
144
131
96
83
55
60
66
Interval
5
13
1
2
5
2
7
36
3
2
4
2
5
16
3
41
10
28
2
15
2
12
2
2
TREO %
0.65
1.23
7.58
0.59
0.69
0.63
2.4
0.94
2.08
1.34
1.14
0.66
0.56
0.77
0.64
2.37
4.07
0.81
2.34
1.09
2.75
1.07
0.67
0.69
Nb205 %
0.15
0.15
0.31
0.05
0.04
0.07
0.14
0.24
0.3
0.05
0.06
0.05
0.1
0.12
0.08
0.51
0.74
0.24
0.18
0.12
0.13
0.07
0.05
0.05
P2O5 %
13.53
8.75
11.94
3.64
2.28
1.11
3.79
8.93
3.83
2.91
4.21
3.68
4.22
3.04
2.54
7.61
7.35
12.39
16.13
23.37
29.11
27.38
20.76
21.77
TREO % = Lanthanide Oxides + Yttrium Oxide + Scandium Oxide
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
5
Appendix 3: JORC Table
JORC Code, 2012 Edition – Table 1
Cummins Range Section 1 Sampling Techniques and Data
Criteria
JORC Code Explanation
Sampling
techniques
Nature and quality of sampling (eg cut channels, random chips, or specific specialised industry
standard measurement tools appropriate to the minerals under investigation, such as down hole
gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as
limiting the broad meaning of sampling.
Include reference to measures taken to ensure sample representivity and the appropriate
calibration of any measurement tools or systems used.
Aspects of the determination of mineralisation that are Material to the Public Report. In cases
where ‘industry standard’ work has been done this would be relatively simple (eg ‘reverse
circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a
30 g charge for fire assay’). In other cases more explanation may be required, such as where
there is coarse gold that has inherent sampling problems. Unusual commodities or
mineralisation types (eg submarine nodules) may warrant disclosure of detailed information.
Drill type (eg core, reverse circulation, open- hole hammer, rotary air blast, auger, Bangka,
sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, facesampling bit or other type, whether core is oriented and if so, by what method, etc).
•
•
•
Reverse circulation (RC) drilling was used for the entire drill program
Method of recording and assessing core and chip sample recoveries and results assessed.
Measures taken to maximise sample recovery and ensure representative nature of the samples.
Whether a relationship exists between sample recovery and grade and whether sample bias
may have occurred due to preferential loss/gain of fine/coarse material.
Whether core and chip samples have been geologically and geotechnically logged to a level of
detail to support appropriate Mineral Resource estimation, mining studies and metallurgical
studies.
Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc)
photography.
The total length and percentage of the relevant intersections logged.
If core, whether cut or sawn and whether quarter, half or all core taken.
If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry.
•
•
Drill sample recovery was logged
Sample recovery for drill holes are CRX0059 97%, CRX0060 97%, CRX0061 98%,
CRX0063 95%, CRX0064 96%, CRX0068 95%. These recoveries exclude the top 3m
where sample recovery is poor due to fine unconsolidated sands.
All metres drilled had a geology log completed. Geology logs were aided using
geochemical analysis from a portable XRF.
The detail of logging is appropriated for Mineral Resource estimation.
Drilling
Techniques
Drill
Sample
Recovery
Logging
Subsampling
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
•
•
•
•
•
•
•
The Cummins Range Rare Earth deposit was drilled tested with RC drilling.
The RC drill rig used a 5 ½ inch diameter hammer. Each 1m bulk sample was collected
in a plastic bag.
Each metre was analysed with a portable XRF, and recovery and geology logs were
completed.
Sample interval selection was based on geological controls and mineralisation
Each 1m bulk sample was split with a riffle splitter to the appropriate size. Samples
varied in length from 1m to 4m.
Samples were assayed for 42 elements using either a peroxide fusion with a ICP-OES
and ICP-MS finish, or a four acid digest with a ICP-OES and ICP-MS finish
Splits from the drill rig were not used. The entire 1m bulk sample was split with a
riffle splitter to the appropriate size. Samples varied in length from 1m to 4m.
6
techniques
and sample
preparation
Quality of
assay data
and
laboratory
tests
Verification
of sampling
and
assaying
For all sample types, the nature, quality and appropriateness of the sample preparation
technique.
Quality control procedures adopted for all sub-sampling stages to maximise representivity of
samples.
Measures taken to ensure that the sampling is representative of the in situ material collected,
including for instance results for field duplicate/second-half sampling.
Whether sample sizes are appropriate to the grain size of the material being sampled.
The nature, quality and appropriateness of the assaying and laboratory procedures used and
whether the technique is considered partial or total
For geophysical tools, spectrometers, handheld XRF instruments, etc, the parameters used in
determining the analysis including instrument make and model, reading times, calibrations
factors applied and their derivation, etc.
Nature of quality control procedures adopted (eg standards, blanks, duplicates, external
laboratory checks) and whether acceptable levels of accuracy (ie lack of bias) and precision have
been established.
The verification of significant intersections by either independent or alternative company
personnel.
The use of twinned holes.
The verification of significant intersections by either independent or alternative company
personnel.
Discuss any adjustment to assay data.
Location of
data points
Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys),
trenches, mine workings and other locations used in Mineral Resource estimation.
Specification of the grid system used.
Quality and adequacy of topographic control.
Data
spacing
and
distribution
Data spacing for reporting of Exploration Results.
Whether the data spacing and distribution is sufficient to establish the degree of geological and
grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s)
and classifications applied.
Whether sample compositing has been applied.
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
•
This sampling technique is better than industry standards and is appropriate for this
style of mineralisation and for resource estimation.
The reported assays were analysed by Nagrom. The following techniques were used:
•
28 elements were assayed for using peroxide fusion with a ICP-OES and ICP-MS finish
•
14 elements were assayed for using four acid digest with a ICP-OES and ICP-MS finish
•
In addition to internal checks by Nagrom, RareX incorporates a QA/QC sample
protocol utilizing prepared standards, blanks and duplicates for 8% of all assayed
samples.
•
•
•
•
•
•
•
•
•
•
•
Significant intercepts were calculated by RareX geological staff.
The intercepts have not been verified by independent persons
There are numerous drill holes with in the Cummins Range resource of comparable
tenure
All assay results are reported to RareX in parts per million (ppm). RareX geological
staff then convert the parts per million to ppm oxides using the below element to
stoichiometric oxide conversion factors. La2O3 1.1728, CeO2 1.2284, Pr6O11 1.2082,
Nd2O3 1.1664, Sm2O3 1.1596, Eu2O3 1.1579, Gd2O3 1.1526, Dy2O3 1.1477, Ho2O3
1.1455, Er2O3 1.1435, Tm2O3 1.1421, Yb2O3 1.1387, Lu2O3 1.1371, Sc2O3 1.5338, Y2O3
1.2699, Nb2O5 1.4305, P2O5 2.2916
Drill hole collars were located by handheld GPS
All coordinates are in MGA Zone 52H 1994
Topographic control is maintained by the use of previously surveyed drill holes. The
Cummins Range deposit is located in flat terrain.
Down hole surveys were taken every 30m, using a digital Reflex multi shot camera.
The purposed of the drill program is to test the new geological model, including new
mineralised structures.
This drill spacing will be sufficient to demonstrate grade continuity to support the
definition of a Mineral Resource as per the JORC 2012 code
2m to 4m composites were completed in areas where higher grades were not
expected
7
Orientation
of data in
relation to
geological
structure
Sample
security
Whether the orientation of sampling achieves unbiased sampling of possible structures and the
extent to which this is known, considering the deposit type.
If the relationship between the drilling orientation and the orientation of key mineralised
structures is considered to have introduced a sampling bias, this should be assessed and
reported if material.
The measures taken to ensure sample security
•
The angled drill holes were directed as best possible across the known geology. The
new geological interpretation is mineralised structures are striking at 320 degrees and
dipping towards the south west at 50-60 degrees. Drill holes testing these structures
are being drilled at 50 degrees azimuth.
•
Drill samples are delivered to Halls Creek by RareX staff. Then the samples are
transported from Halls Creek to Perth via a reputable transport company.
Cummins Range Section 2 Reporting of Exploration Results
Criteria
Mineral
tenement and
land tenure
status
Exploration
done by other
parties
JORC Code Explanation
Type, reference name/number, location and ownership including agreements or material
issues with third parties such as joint ventures, partnerships, overriding royalties, native title
interests, historical sites, wilderness or national park and environmental settings.
The security of the tenure held at the time of reporting along with any known impediments to
obtaining a licence to operate in the area.
Acknowledgment and appraisal of exploration by other parties.
•
•
Geology
Deposit type, geological setting and style of mineralisation.
•
Drill hole
information
A summary of all information material to the understanding of the exploration results
including a tabulation of the following information for all Material drill holes:
easting and northing of the drill hole collar
•
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
The Cummins Range REO deposit is located on tenement E80/5092 and is 100%
owned by Cummins Range Pty Ltd which is a wholly owned subsidiary of RareX Ltd.
Cummins Range Pty Ltd has purchased the tenement from Element 25 with a
potential capped royalty payment of $1m should a positive PFS be completed within
36 months of purchase finalisation.
CRA Exploration defined REO mineralisation at Cummins Range in 1978 using
predominantly aircore drilling. Navigator Resources progressed this discovery with
additional drilling after purchasing the tenement in 2006. Navigator announced a
resource estimate in 2008. Kimberly Rare Earths drilled additional holes and upgraded
the resource estimate in 2012.
The Cummins Range REO deposit occurs within the Cummins Range carbonatite
complex which is a 2.0 km diameter near-vertical diatreme pipe that has been deeply
weathered but essentially outcropping with only thin aeolian sand cover in places.
The diatreme pipe consists of various mafic to ultramafic rocks with later carbonatite
intrusions. The primary or fresh ultramafic and carbonatite rocks host low to high
grade rare earth elements with back ground levels of 1000-2000ppm TREO and high
grade zones up to 8% TREO. The current resource sits primarily within the
oxidised/weathered zone which reaches to 120m below the surface. Metallurgical
studies by previous explorers show the rare earth elements are hosted by Monazite
which is a common and favourable host for rare earth elements.
Drill collar details are in the collar table. Cummins Range is located on very flat terrain
and the RL is at 391m to 392m. All drill holes are drilled from this RL.
8
Data
aggregation
methods
Relationship
between
mineralisation
widths and
intercept
lengths
Diagrams
Balanced
reporting
Other
substantive
exploration
data
elevation or RL (Reduced Level – elevation above sea level in metres) of the drill hole
collar
dip and azimuth of the hole
down hole length and interception depth
hole length.
If the exclusion of this information is justified on the basis that the information is not Material
and this exclusion does not detract from the understanding of the report, the Competent
Person should clearly explain why this is the case.
In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum
grade truncations (eg cutting of high grades) and cut-off grades are usually Material and
should be stated.
Where aggregate intercepts incorporate short lengths of high grade results and longer
lengths of low grade results, the procedure used for such aggregation should be stated and
some typical examples of such aggregations should be shown in detail.
The assumptions used for any reporting of metal equivalent values should be clearly stated.
These relationships are particularly important in the reporting of Exploration Results
If the geometry of the mineralisation with respect to the drill hole angle is known, its nature
should be reported.
If it is not known and only the down hole lengths are reported, there should be a clear
statement to this effect (eg ‘down hole length, true width not known’).
Appropriate maps and sections (with scales) and tabulations of intercepts should be included
for any significant discovery being reported These should include, but not be limited to a plan
view of drill hole collar locations and appropriate sectional views.
Where comprehensive reporting of all Exploration Results is not practicable, representative
reporting of both low and high grades and/or widths should be practiced to avoid misleading
reporting of Exploration Results.
Other exploration data, if meaningful and material, should be reported including (but not
limited to): geological observations; geophysical survey results; geochemical survey results;
bulk samples – size and method of treatment; metallurgical test results; bulk density,
groundwater, geotechnical and rock characteristics; potential deleterious or contaminating
substances.
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
•
•
Significant intercepts were calculated using weighted averaging
A lower cut off of 0.5% Lanthanide Oxides + Y2O3 + Sc2O3 was used with a maximum
of 5m dilution. This cut off grade and dilution is thought to be appropriate due to
likely open cut mining methods that would be used on the outcropping ore body.
•
RareX are currently testing a geological model that the primary source of the REE are
concentrated in structures and as the structures are weathered the monazite is being
dispersed and concentrated in the regolith. RareX are drilling these structures at 50
degrees azimuth to confirm the structures true width. This first phase of drilling has
confirmed the model in the areas that have been drilled. Mineralised intervals appear
to be very close to truth width. However further drilling will be needed to firm up the
geological model. Diamond drilling has commenced and will be testing the
mineralisation in fresh rock.
•
Maps and diagrams are included in the body of the announcement
•
Reporting is considered balanced
•
This announcement describes the first batch of assays and further assays are
expected to be delivered on a regular basis to the end of the year.
9
Further work
The nature and scale of planned further work (eg tests for lateral extensions or large scale
step out drilling.
Diagrams clearly highlighting the areas of possible extensions, including the main geological
interpretations and future drilling areas, provided this information is not commercially
sensitive.
RareX Limited
Unit 6, 94 Rokeby Road, Subiaco WA 6008 Ph: 08 6383 6593 ACN: 105 578 756
•
•
•
•
Drilling will continue for the next few months
Geological model continues to be developed
Water monitoring bores for mining studies will be drilled next month
Metallurgical studies are on going
10
Share your feedback
Discover